Page 1 of 2
Barrel hold with revolver
Posted: Wed Feb 25, 2015 3:43 am
by jmoore
Would require glove and arm protection, I reckon, but seems to work well dry firing on a long barreled S&W that has just had a 30mm reddot installed.
Just wondering if anyone has been nutty enough to have already tried it?
next decent range day, I intend on doing it as a test with some not particularly warm .44 CB loads.
Re: Barrel hold with revolver
Posted: Wed Feb 25, 2015 8:46 am
by ole95
Shot with a guy in NM that did was shooting
NRA BB standing i was shooting a 7tcu contender
And i had more bady damage than he did
Dont remember the gun are cal he used
Re: Barrel hold with revolver
Posted: Fri Feb 27, 2015 12:11 am
by jmoore
Thanks for input! May be an experiment put on hold until after the next match, what with the weather and end of squirrel season and all. Two more days to try and find a fox squirrel for the season. Deer are more plentiful in these parts!
Re: Barrel hold with revolver
Posted: Fri Feb 27, 2015 7:12 pm
by Jimologist
Saw a guy at the 2008? International shoot taco with a 44? Or a .445 SM?
The flame from the cylinder gap pretty effectively cauterizes the wound.
Somebody help me with his name, he rode a motorcycle and called him Big Noise. Mike Big Noise.
He was one tough dude. He did not stop after the first shot and continued to shoot until we made him stop.
Only time I have ever seen it done and he was bleeding from the left forearm.
Jim k
Re: Barrel hold with revolver
Posted: Fri Feb 27, 2015 9:32 pm
by 260 Striker
Sounds like he needed a blast shield for his arm!!!
Re: Barrel hold with revolver
Posted: Sat Feb 28, 2015 10:53 am
by 35isit
IIRC Mr. Puffert at Crittenden Ky used to shoot a 32-20 Dan Wesson with a welders glove. It had a rifle scope and he held it in the Taco position when Field pistol first started.
Re: Barrel hold with revolver
Posted: Mon Mar 02, 2015 5:14 am
by jmoore
I have a welder's coat and gloves, but the glove seems too thick. I do have an old thin glove with a couple of squirrel hides sewn on (round about 2003, IIRC) that I use when shooting muzzleloaders. It's worked to keep cap fragments and powder away so far! Getting kinda tatty, though. Fur's starting to fall off...
Maybe this AM there will be live fire testing!
Re: Barrel hold with revolver
Posted: Tue Mar 03, 2015 12:44 am
by jmoore
Well, that was a non-event! Felt a little weird in recoil, but no flesh wounds or nuttin'. Untested revolver and new loads, but seems promising. Hope to try it this weekend at the monthly match.
Re: Barrel hold with revolver
Posted: Tue Mar 03, 2015 5:55 pm
by captainjohn
Jim, that was Mike Stanley from Wisconsin. He didn't shoot standing but thought he could trophy in his class,all he had extra ammo for was his SW .44 mag.Shot a few rounds till he couldn't take the pain/Blood anymore.Mike dropped off the face of the earth years ago.We heard he came into a pile of $$
Re: Barrel hold with revolver
Posted: Wed Mar 04, 2015 2:41 am
by jmoore
Here's the test subject. Test reddot, revolver, ammo, hold. Ought to be an interesting trial! Generally acceptable on bullseye targets at 25 and 50yards. May not have a chance to try 100yd before the match. No 75yard opportunities at my usual range.
