What equipment are you using to size your bullets? Based on your stated experience, it must be a lubrisizer......either a Lyman or an RCBS. What is the specification on your sizer die?...........284" .285" .286"?
It also sounds like your alloy is too soft if you are able to "bump up" the bullet that much while sizing. You said wheel weight metal. Is it all clip-on weights or are there some stick-on weights included. You could drop those bullets straight from the mold into a bucket of water and you will gain some hardness which should give you less problems with the "bumping up" in diameter. The harder bullet could actually help with accuracy as well.
We can also learn more if you can get that chamber cast. It is always best to start with that. You can avoid all the guess work that you run into if you don't do the chamber cast first. I use the "impact chamber cast" method. It's very easy to do.
7x30 waters cast bullet extending into neck? good/bad?
- high standard 40
- Class A
- Posts: 657
- Joined: Mon Feb 07, 2011 8:08 am
- IHMSA Member#: 11568
Re: 7x30 waters cast bullet extending into neck? good/bad?
IHMSA Member since 1980
Former Match Director Baton Rouge Silhouette Club
Current Match Director Ascension Silhouette
Current Match Director Saline Creek Silhouette
Current Match Director Top Shot Silhouette
NRA Life Member
NRA Range Safety Officer
Former Match Director Baton Rouge Silhouette Club
Current Match Director Ascension Silhouette
Current Match Director Saline Creek Silhouette
Current Match Director Top Shot Silhouette
NRA Life Member
NRA Range Safety Officer
-
- Target Painter
- Posts: 29
- Joined: Sat Feb 07, 2015 11:53 pm
- IHMSA Member#: 0
Re: 7x30 waters cast bullet extending into neck? good/bad?
i use a rcbs lubrisizer with a .285 sizing die. i drop my bullets from the mold straight into a five gallon bucket of water. i use wheel weights with the steel clips and hadn't thought about NOT throwing in the stick on weights, although now i can see i won't be doing that again.
I spent some time on both guns and cleaned out the copper fouling from the barrels pretty good i think. i have had zero leading in either barrel. so i assumed the lead bullets were hard enough. i don't have a lead tester. i do own about 30 lbs. of linotype so i could add some of that to the mix, perhaps a one to ten ration would be good?
I will do an impact chamber cast and report back to ya.
as always, thanks for helping me out, greatly appreciate it.
I spent some time on both guns and cleaned out the copper fouling from the barrels pretty good i think. i have had zero leading in either barrel. so i assumed the lead bullets were hard enough. i don't have a lead tester. i do own about 30 lbs. of linotype so i could add some of that to the mix, perhaps a one to ten ration would be good?
I will do an impact chamber cast and report back to ya.
as always, thanks for helping me out, greatly appreciate it.
Re: 7x30 waters cast bullet extending into neck? good/bad?
Could you please educate me and describe the "impact chamber cast" method.high standard 40 wrote:What equipment are you using to size your bullets? Based on your stated experience, it must be a lubrisizer......either a Lyman or an RCBS. What is the specification on your sizer die?...........284" .285" .286"?
It also sounds like your alloy is too soft if you are able to "bump up" the bullet that much while sizing. You said wheel weight metal. Is it all clip-on weights or are there some stick-on weights included. You could drop those bullets straight from the mold into a bucket of water and you will gain some hardness which should give you less problems with the "bumping up" in diameter. The harder bullet could actually help with accuracy as well.
We can also learn more if you can get that chamber cast. It is always best to start with that. You can avoid all the guess work that you run into if you don't do the chamber cast first. I use the "impact chamber cast" method. It's very easy to do.
Thanks
Pete
Ontario Provincial Director
Match Director, Galt Sportsmen's Club
Ontario Provincial Director
Match Director, Galt Sportsmen's Club
- high standard 40
- Class A
- Posts: 657
- Joined: Mon Feb 07, 2011 8:08 am
- IHMSA Member#: 11568
Re: 7x30 waters cast bullet extending into neck? good/bad?
I posted a link to a detailed explanation of the process in a previous discussion on this forum a couple of weeks ago. Here it is again.borregos wrote:Could you please educate me and describe the "impact chamber cast" method.high standard 40 wrote:What equipment are you using to size your bullets? Based on your stated experience, it must be a lubrisizer......either a Lyman or an RCBS. What is the specification on your sizer die?...........284" .285" .286"?
It also sounds like your alloy is too soft if you are able to "bump up" the bullet that much while sizing. You said wheel weight metal. Is it all clip-on weights or are there some stick-on weights included. You could drop those bullets straight from the mold into a bucket of water and you will gain some hardness which should give you less problems with the "bumping up" in diameter. The harder bullet could actually help with accuracy as well.
We can also learn more if you can get that chamber cast. It is always best to start with that. You can avoid all the guess work that you run into if you don't do the chamber cast first. I use the "impact chamber cast" method. It's very easy to do.
Thanks
http://castboolits.gunloads.com/showthr ... amber+slug
Last edited by high standard 40 on Fri Mar 06, 2015 8:50 pm, edited 1 time in total.
IHMSA Member since 1980
Former Match Director Baton Rouge Silhouette Club
Current Match Director Ascension Silhouette
Current Match Director Saline Creek Silhouette
Current Match Director Top Shot Silhouette
NRA Life Member
NRA Range Safety Officer
Former Match Director Baton Rouge Silhouette Club
Current Match Director Ascension Silhouette
Current Match Director Saline Creek Silhouette
Current Match Director Top Shot Silhouette
NRA Life Member
NRA Range Safety Officer
Re: 7x30 waters cast bullet extending into neck? good/bad?
Many thanks.high standard 40 wrote:I posted a link to a detailed explanation of the process in a previous discussion on this forum a couple of weeks ago. Her it is again.borregos wrote:Could you please educate me and describe the "impact chamber cast" method.high standard 40 wrote:What equipment are you using to size your bullets? Based on your stated experience, it must be a lubrisizer......either a Lyman or an RCBS. What is the specification on your sizer die?...........284" .285" .286"?
It also sounds like your alloy is too soft if you are able to "bump up" the bullet that much while sizing. You said wheel weight metal. Is it all clip-on weights or are there some stick-on weights included. You could drop those bullets straight from the mold into a bucket of water and you will gain some hardness which should give you less problems with the "bumping up" in diameter. The harder bullet could actually help with accuracy as well.
We can also learn more if you can get that chamber cast. It is always best to start with that. You can avoid all the guess work that you run into if you don't do the chamber cast first. I use the "impact chamber cast" method. It's very easy to do.
Thanks
http://castboolits.gunloads.com/showthr ... amber+slug
Pete
Ontario Provincial Director
Match Director, Galt Sportsmen's Club
Ontario Provincial Director
Match Director, Galt Sportsmen's Club
- marshall623
- Spotter
- Posts: 93
- Joined: Sun Feb 06, 2011 3:52 pm
- IHMSA Member#: 57357
Re: 7x30 waters cast bullet extending into neck? good/bad?
Had the same issues with my 7-30 , I thought I was putting a nice me plate on that Lee bullet, but it was bumping up the nose dia. It doesn't take much pressure to do it either.
-
- Target Painter
- Posts: 29
- Joined: Sat Feb 07, 2015 11:53 pm
- IHMSA Member#: 0
Re: 7x30 waters cast bullet extending into neck? good/bad?
Hey Marshall did ya figure out a way to keep it from happening?
- marshall623
- Spotter
- Posts: 93
- Joined: Sun Feb 06, 2011 3:52 pm
- IHMSA Member#: 57357
Re: 7x30 waters cast bullet extending into neck? good/bad?
Not any good way , but just only enough pressure to seat the check. I think I use the 641 top punch . I have the top punch listed for the 135gr. Lyman bullet also . Neither are a exact fit on the 130 lee. There is a guy on cast boolets who can make custom nose punches. A couple of the nose punch's the Lyman 4th. Cast bullet book list for Lee bullets are not too good of fits that I found either. Close
-
- Target Painter
- Posts: 29
- Joined: Sat Feb 07, 2015 11:53 pm
- IHMSA Member#: 0
Re: 7x30 waters cast bullet extending into neck? good/bad?
Marshal do you have success shooting the lee bullet as far as accuracy goes? I was hoping to use it for silhouettes, but to me, if it doesn't work after fitting it for the barrel (ie, slip fit on the muzzle end) and extending the bullet into the grooves up to the driving bands, I guess i can't see a point in trying to make it work.
I am planning on doing as high standard suggests and making a cast of the 7x30 contender chamber, but i don't see how that info is gonna help a bullet that just isn't gonna perform no matter what. My next step is to look at my casting process with wheel weights. i know i have been cutting corners as far as keeping the heat correct and oxidation, so I'm gonna fix those issues, and we'll go from there.
But if the bullet has a low percentage of people using it due to a reputation of NOT being an accurate bullet, then why waste my time?!? So let me know how it's been working for you please. I also got the 641 punch I believe, it's seems to work really well for me.
I am planning on doing as high standard suggests and making a cast of the 7x30 contender chamber, but i don't see how that info is gonna help a bullet that just isn't gonna perform no matter what. My next step is to look at my casting process with wheel weights. i know i have been cutting corners as far as keeping the heat correct and oxidation, so I'm gonna fix those issues, and we'll go from there.
But if the bullet has a low percentage of people using it due to a reputation of NOT being an accurate bullet, then why waste my time?!? So let me know how it's been working for you please. I also got the 641 punch I believe, it's seems to work really well for me.
- marshall623
- Spotter
- Posts: 93
- Joined: Sun Feb 06, 2011 3:52 pm
- IHMSA Member#: 57357
Re: 7x30 waters cast bullet extending into neck? good/bad?
I've had decent accuracy with the Lee , I run them over 18.5 gr. Of 45 with good results. The Lyman 160 or 145 RCBS are better designs in my opinion. Shoot a few and see , I still use that bullet in the waters & TCU. Because I use a 2 load system in those guns. I would like to see lee put out a heavier 7mm. Bullet. I've heard good things about NOE 's 7mm 150 gr. Hunter