Search found 189 matches
- Sun May 06, 2018 10:13 pm
- Forum: Range Ramblings
- Topic: FINALLY!!
- Replies: 2
- Views: 1354
FINALLY!!
After multiple postponements due to ugly weather, the OKC Gun Club was finally able to have a match today. The weather could not have been much better. There was a decent turnout and I was able to shoot my first 40 (+5) in UAS Small Bore with my Exemplar. Previous attempts were always thwarted by st...
- Fri May 04, 2018 11:35 am
- Forum: Range Ramblings
- Topic: IHMSA News
- Replies: 19
- Views: 8998
Re: IHMSA News
Got mine yesterday, central Oklahoma.
- Sat Apr 21, 2018 9:58 am
- Forum: Reloading
- Topic: Best dies for .357 Max
- Replies: 14
- Views: 8056
Re: Best dies for .357 Max
Consider the RCBS 3 die set #18212. Carbide sizer die needs no lube. Available from Amazon/Midway for a little over $50.00, plus shipping.
- Thu Apr 12, 2018 2:03 pm
- Forum: IHMSA News
- Topic: 2018 IHMSA news.
- Replies: 3
- Views: 3133
Re: 2018 IHMSA news.
Got it, thanks!StandingTall wrote:http://ihmsa.org/ihmsa-news.html
BTW, that Daisy is a tack driver.
- Thu Apr 12, 2018 12:22 pm
- Forum: IHMSA News
- Topic: 2018 IHMSA news.
- Replies: 3
- Views: 3133
Re: 2018 IHMSA news.
Maybe it is just me but where is the link to the newsletter? When I click on "IHMSA NEWS" on the index page it brings me back to this message post. I do not have an embedded link showing in the post.
- Tue Apr 03, 2018 9:43 pm
- Forum: Range Ramblings
- Topic: MAKING APERTURES FOR PEEPS
- Replies: 11
- Views: 4617
Re: MAKING APERTURES FOR PEEPS
Thanks, much appreciated.
- Tue Apr 03, 2018 3:21 pm
- Forum: Range Ramblings
- Topic: MAKING APERTURES FOR PEEPS
- Replies: 11
- Views: 4617
Re: MAKING APERTURES FOR PEEPS
Just made this one and used black Delrin for the insert. I'm going to do another with black acrylic. Delrin machines like butter but it tends to be "stringy" and something this small is a SOB to deburr. The hole is .070 and the O.D. of the insert is .125. O.D. of the whole disc is .682. ht...
- Mon Apr 02, 2018 9:28 pm
- Forum: Range Ramblings
- Topic: MAKING APERTURES FOR PEEPS
- Replies: 11
- Views: 4617
Re: MAKING APERTURES FOR PEEPS
One thing about cast acrylic is that it can vary somewhat from its specified thickness. The piece from which I am working is .125 nominal but is averaging about .110. I like the .125 nominal material as it has enough meat to make sure the insert goes in straight. Of the three I cut in this pic, one ...
- Mon Apr 02, 2018 1:00 pm
- Forum: Range Ramblings
- Topic: MAKING APERTURES FOR PEEPS
- Replies: 11
- Views: 4617
Re: MAKING APERTURES FOR PEEPS
I start with cast (not extruded!) acrylic sheet and I leave the factory masking on. I next cut it into small squares and drill a .093 pilot hole in the center and stack them on a .093 dowel pin. I usually saw the corners off of the squares to make turning a little quicker and less likely to catch. T...
- Sun Apr 01, 2018 5:51 pm
- Forum: Range Ramblings
- Topic: MAKING APERTURES FOR PEEPS
- Replies: 11
- Views: 4617
MAKING APERTURES FOR PEEPS
Turning acrylic between centers for peep sight apertures.
![Image](http://pages.Suddenlink.net/7722/APERTURES.jpg)
![Image](http://pages.Suddenlink.net/7722/APERTURES.jpg)